Microcom Technologies Commander General Purpose Variable Speed Drive GpLV Manuel d'utilisateur télécharger pdf (Page 36)

Commander GP User Guide

Issue code: gpxu2

3-8 Setting Up the Drive

Stopping and braking modes

Refer to the following parameters in Appendix D

Menu 0 Parameters:

Parameter Setting Function

0.150.15

Ramp mode selector

Stnd.Ct

(Standard controlled)

Deceleration time is

extended if the

DC-bus

voltage reaches its

maximum permissible

value during braking.

0.160.16

Stop mode selector

Ramp to stop then the

Drive is disabled

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 117 118

COMMANDERGGpp 1
COMMANDERGGpp LVLV 1
General information 2
Important 2
Contents 3
Commander GP User Guide 4
Issue code: gpxu2 4
1 Introduction 5
1.3 Configuration layers 6
1.4 Default configurations 6
1.5 Operating mode 6
1.6 User-interface modes 6
1.7 Macro configurations 7
1.8 Plug-in option modules 8
1.9 Serial communications 8
Introduction 1-5 9
1-6 Introduction 10
2 Getting Started 11
2-2 Getting Started 12
Getting Started 2-3 13
2-4 Getting Started 14
Getting Started 2-5 15
2.3 Introduction to the 16
2.4 Working with 17
2.5 How macro configurations 18
2.6 Initial setting up 19
2-10 Getting Started 20
Enabling Macro 1 20
Getting Started 2-11 21
2-12 Getting Started 22
Autotune 22
2.7 Operating instructions 23
2-14 Getting Started 24
Keypad mode 24
Trip and enable 24
Getting Started 2-15 25
Acceleration rate 25
Deceleration rate 25
Braking resistor 25
2-16 Getting Started 26
Voltage-control modes 26
Getting Started 2-17 27
Boost voltage 27
2-18 Getting Started 28
3 Setting Up the Drive 29
(Macro Configurations) 29
General purpose 30
Setting Up the Drive 3-3 31
3-4 Setting Up the Drive 32
Setting Up the Drive 3-5 33
3-6 Setting Up the Drive 34
Setting Up the Drive 3-7 35
Setting up and using Macro 0 35
3-8 Setting Up the Drive 36
Easy mode 37
3-10 Setting Up the Drive 38
Setting Up the Drive 3-11 39
3-12 Setting Up the Drive 40
Setting Up the Drive 3-13 41
Setting up and using Macro 1 41
3-14 Setting Up the Drive 42
Motorized potentiometer 43
3-16 Setting Up the Drive 44
Setting Up the Drive 3-17 45
3-18 Setting Up the Drive 46
Setting Up the Drive 3-19 47
Setting up and using Macro 2 47
3-20 Setting Up the Drive 48
Preset frequencies 49
3-22 Setting Up the Drive 50
Setting Up the Drive 3-23 51
3-24 Setting Up the Drive 52
Setting Up the Drive 3-25 53
Setting up and using Macro 3 53
3-26 Setting Up the Drive 54
Torque control 55
FREQUENCY CONTROL 55
TORQUE CONTROL 55
3-28 Setting Up the Drive 56
Setting Up the Drive 3-29 57
3-30 Setting Up the Drive 58
Setting Up the Drive 3-31 59
Setting up and using Macro 4 59
3-32 Setting Up the Drive 60
PID (set-point control) 61
PID CONTROL 61
3-34 Setting Up the Drive 62
Setting Up the Drive 3-35 63
3-36 Setting Up the Drive 64
Setting Up the Drive 3-37 65
Setting up and using Macro 5 65
Axis-limit control 66
Setting Up the Drive 3-39 67
3-40 Setting Up the Drive 68
Setting Up the Drive 3-41 69
3-42 Setting Up the Drive 70
Setting Up the Drive 3-43 71
Setting up and using Macro 6 71
3-44 Setting Up the Drive 72
Brake control 73
3-46 Setting Up the Drive 74
Setting Up the Drive 3-47 75
3-48 Setting Up the Drive 76
Setting Up the Drive 3-49 77
Setting up and using Macro 7 77
3-50 Setting Up the Drive 78
A Programming 79
Instructions 79
A-2 Programming Instructions 80
A.6 Selecting 81
A.7 Changing the value of a 82
Programming Instructions A-5 83
A-6 Programming Instructions 84
A.13 Restoring the Drive 85
A-8 Programming Instructions 86
B Security 87
B-2 Security 88
C Signal Connections 89
C-2 Signal Connections 90
Signal Connections C-3 91
C-4 Signal Connections 92
D Menu 0 Parameters 93
D.2 Fixed-function parameters 94
Menu 0 Parameters D-3 95
D-4 Menu 0 Parameters 96
Voltage boost 96
PWM switching frequency 98
Menu 0 Parameters D-7 99
Motor parameters 99
Drive software build number 99
Status information 99
D.3 Parameters specific 100
Menu 0 Parameters D-9 101
D-10 Menu 0 Parameters 102
Menu 0 Parameters D-11 103
D-12 Menu 0 Parameters 104
Menu 0 Parameters D-13 105
D-14 Menu 0 Parameters 106
Menu 0 Parameters D-15 107
D-16 Menu 0 Parameters 108
Menu 0 Parameters D-17 109
D-18 Menu 0 Parameters 110
Menu 0 Parameters D-19 111
D-20 Menu 0 Parameters 112
Menu 0 Parameters D-21 113
D-22 Menu 0 Parameters 114
E Diagnostics 115
E.3 Trip codes 116
Diagnostics E-3 117
E-4 Diagnostics 118

Commentaires sur ces manuels

Pas de commentaire

Microcom Technologies Commander General Purpose Variable Speed Drive GpLV Manuel d'utilisateur Page 36

Commentaires sur ces manuels